The hydraulic oil pump acts as the power heart of a hydraulic system. Once it fails, common issues will occur, including insufficient pressure, weak movement, abnormal noise, oil leakage and rapid oil temperature rise. When equipment breaks down, many maintenance technicians struggle to tell whether the problem comes from valve components or a damaged oil pump. Mastering correct inspection steps helps you quickly check if your hydraulic pump is good or bad, avoid misjudgment and cut maintenance costs.
1.1 Check External Oil Leakage:
Inspect the pump housing, shaft seal and port fittings. Continuous oil seepage at the shaft or leakage from casting pores on the housing usually means aging seals or pump body wear. Minor seepage may be solved by replacing seals. Cracked housing and heavy leakage indicate a failed pump.
Note: Oil leakage caused by loose connectors is not a pump body failure. Tighten fittings before further testing.
1.2 Check Hydraulic Oil Condition:
Open the oil tank and inspect hydraulic oil. If plenty of metal powder or debris is found in the oil, the internal gear, piston or vane of the pump has severe wear and scuffing, and the pump is mostly invalid. Dark and contaminated oil will also accelerate pump damage.
1.3 Inspect Mounting and Coupling:
Check whether the coupling is loose or the elastic cushion is broken. In many cases, abnormal noise does not come from the pump, but damaged coupling, which is easy to misdiagnose as pump failure.
A healthy hydraulic pump runs with smooth, low and steady sound. The following abnormal noises indicate pump faults:
2.1 Sharp whistling noise:
Usually caused by insufficient oil suction, air leakage in suction pipeline, blocked filter element or low oil level, resulting in cavitation noise.
2.2 Knocking or impact sound:
Damaged internal bearings, worn gears or piston assemblies, meaning internal parts of the pump are damaged.
2.3 Continuous dull noise:
Enlarged internal clearance from wear, leading to serious internal leakage.
Tip: If abnormal noise is obvious during idling and gets louder under load, the pump is highly likely damaged.
Pressure testing is the most effective way to verify hydraulic pump performance, requiring a pressure gauge and pressure test connector.
3.1 Connect the pressure gauge to the pressure test port at the pump outlet.
3.2 Start the equipment and gradually load the system.
3.3 Read the pressure gauge:
✅ Pressure can reach the rated value and stay stable → The pump is basically in good condition
❌ Pressure cannot reach the rated value on nameplate even after adjusting the relief valve → Severe internal leakage, pump damaged
⚠️ Note: Low pressure is not always caused by the oil pump. Stuck relief valve or leaking check valve may also lead to low pressure. Isolate valve parts to test the pump separately.
The most common failure of oil pumps is internal leakage. No external signs can be seen, but output flow drops, causing slow cylinder movement and weak lifting force.
4.1 Flow Test (Recommended):
Use a flow meter to measure the actual output flow of the pump. If the actual flow under load is far lower than the rated flow marked on the nameplate, internal wear and excessive internal leakage occur.
4.2 Simple Internal Leakage Test:
Block the oil outlet and carry out short pressure holding test. If pressure drops quickly, the internal sealing or valve plate is worn, with excessive internal leakage and pump failure.
Many malfunctions do not result from the pump itself. Make careful distinction during maintenance to prevent unnecessary pump replacement:
5.1 Insufficient system pressure: possible causes include pump internal leakage, relief valve failure, cylinder internal leakage, pipeline leakage
5.2 Abnormal pump noise: air intake on suction side, insufficient oil, clogged filter, damaged coupling, bearing damage
5.3 Rising oil temperature: pump internal leakage, long-term overload, cooling system failure
5.4 Weak movement: check pressure first, then flow, and finally confirm whether the oil pump is faulty
Follow this sequence to check your oil pump: Visual inspection → Listen for running noise → Check oil impurities → Pressure test → Flow & internal leakage test.Rule out external factors such as oil suction issues, valve faults, coupling and hydraulic oil condition before confirming pump damage. This helps avoid replacing a functional pump at high cost.Regular hydraulic oil maintenance and suction filter replacement can reduce impurities entering the pump and greatly extend the service life of the hydraulic oil pump.
Contact: Mr.Qiu
Phone: 18959452627
E-mail: qiuyueyun@lyunite.com
Whatsapp:+8618959452627
Add: Room 1502, Unit 1, Building 5, No.1 Wuxing Road, Xinluo District, Longyan City, Fujian Province